Hammered Dulcimer Accessories

Adjustable stand

Adjustable height by quick release knobs. Adjustable playing angle by easy turn of screwdriver. Unassembled. Assembly requires a screwdriver and takes approx 10 minutes to complete.

Ash is a light colored hard wood and does not have a finish on it. Apply a stain or finish if desired. Walnut is a dark brown wood. Cherry is a medium pinkish brown wood. Walnut and cherry have a satin finish.
Item# DS6A Ash, DS6W Walnut, DS6C Cherry

Wood choices for stand
Walnut, cherry, and ash

Stand shown in ash.

Stand shown in walnut.

Scissors stand

Lightweight but sturdy, made of pine or ash. Cushioned instrument supports.

Sit down stand is 28" high and folds to a compact size of 36" x 3 1/4". 3 to 4 lbs.
Item# DS2

Stand up version is 37" high. 4lbs
Item# DS4

St. Brigit Cross
8 inch length. Double sided with bare wood on one side, leather covered on other side. Canary, Walnut, Zebra, and Maple (shown left to right). Grips are a complementary wood. Select picture for larger view of hammers. Sold as a pair. Made by Jill Weimer.
Item# HJW1

Ed Hale Hammers 1
8.25" to 8.5" length. Double sided with bare wood on one side, leather covered on other side. Cherry.  Grips vary with complementary wood.   Sold as a pair. Made by Ed Hale.
Item# HEH1

Available  in 2 head sizes: smaller head or larger head.   The difference in sizes is approx. 1/4 inch in length and 1/8 inch in width.

Korg AW-2G
Korg AW-2G chromatic clip-on tuner. Designed for guitar, bass, mandolin but works well on hammered dulcimers.  Clips onto bridge.  Backlit display for higher visibility.  Multi-angle adjustment for easy viewing.  Combines Piezo pickup and built-in microphone. Battery included. 
Item# ET2

Korg CA-1
Korg CA1 chromatic tuner with easy to read VU meter for automatic mode. Also has built in 12 note reference tones. Can be used for many chromatic instruments . Pitch detection from C1 - C8. Built in mic. Also input jack for pickup. Tilt slot on back allows you to insert a plastic card to angle meter for easy viewing. Two AAA batteries included. 

The CA-1 replaces the popular CA30 but at a reduced price.

Item# ET1

Tuner Pickup

Eliminate noise interference when tuning with a pick-up. Plugs into most major brand tuners with input jacks and clips onto instrument.

Signal Flex SF-30 has padded clip-on w/5 ft. cord.  Suitable for clamping onto a bridge.
Item# ET-P1

Alligator clip-on has metal jaws clip-on w/30 inch cord. Suitable for clamping onto a pin.
Item# ET-P2

Tuning Wrenches

Available in a gooseneck with square head or T handle with star head version.  Both styles work on most zither/tuning pins.

Gooseneck handle with square head
Item# TW3

T handle with star head
Item# TW2

Duster

Chinese hog bristles in a hand turned hardwood handle. 4" bristles make it ideal for reaching through dulcimer strings.
Item# AHD-D

Music Stand for Hammered Dulcimer

The bottom section fits between the underside of your dulcimer and a dulcimer stand that has a center support leg. The top section holds your music and has a wingnut adjustment for the angle.
AHD-MS1 has the note cutout in the top section and is shown in picture. 
AHD-MS2 version is not shown but has a plain top section (no note cutout) and the top section is 2 1/2 inches taller. The extra height is helpful when being used outside to keep the wind from blowing the music off the holder.